 |
|
|
1-888-492-6526
DATA CONNECT ANS206-FT
6-PORT INDUSTRIAL 10/100 FIBER SWITCH
Plastic Casing ANS206-FT 4 10/100 ports + 2 100 Base-FX fiber-ST ANS206-MM 4 10/100 ports + 2 100 Base-FX fiber-Multimode SC ANS206-SM 4 10/100 ports + 2 100 Base-FX fiber-Single mode SC |
Metal Casing ANS206-FT-M 4 10/100 ports + 2 100 Base-FX fiber-ST+metal ANS206-MM-M 4 10/100 ports + 2 100 Base-FX fiber-Multimode SC+metal ANS206-SM-M 4 10/100 ports + 2 100 Base-FX fiber-Single mode SC+metal |
|
|
The Data Connect ANS206-FT (ST Connector; Multi-mode) is a Unmanaged 4-Port Industrial 10/100 Base-T(X) with Dual 100 Base-FX Switch that secures data transmission by using fiber optic transmission to provide immunity from EMI/RFI interference. It is used Ethernet for transmitting a signal up to 2 Km(6,600 ft), and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.
The Data Connect ANS206-FT operates at either half or full duplex mode. In full duplex mode, range is 2km with 62.5/ 125μm fiber cables; in half duplex mode, range is 412m with 62.5/ 125μm fiber cables.
The Data Connect ANS206-FT can extend your LAN in a daisy chain configuration. Please refer to Hardware.
The Ethernet supports 10/ 100M auto-negotiation feature and auto MDI /MDIX function.
- Automatic MDI / MDI-X crossover for plug-and-play
- Each port supports both 10/100 Mbps speed auto negotiation
- Store-and-forward architecture
- Full duplex IEEE 802.3x and half duplex backpressure flow control
- 1.6 Gbps high performance memory bandwidth
- Frame buffer memory : 256 Kbit
- Integrated look-up engine with dedicated 1 K unicast MAC addresses.
- Supports +10~+30Vdc voltage
- Supports operating temperatures from 0 ~ +70°C
- DIN rail mount for industrial usage
| Technology | |
| Standards | IEEE802.3, 802.3u, 802.3x |
| Processing Type | Store & forward wire speed switching - no delays |
| MAC Addresses | 1024 |
| Memory Bandwidth | 1.6 Gbps |
| Flow Control | IEEE802.3x flow control, back pressure flow control |
| Interface | |
| RJ45 port |
10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDIX connection |
| Fiber Optic port | 100 Base-FX(Multi-mode; ST connector) |
| LED Indicators | 10/100M, Link/Act, Full duplex/Half duplex(Fiber Port) |
| Ethernet Isolation | 1500 Vrms 1 minute |
| Frame Ground for EMS Protection | Yes |
| Fiber Optic | Multi mode fiber cables:50/125, 62.5/125 or 100/140 μm |
| Distance :2 km, (62.5/125 μm recommended) for full duplex | |
| Wavelength : 1300 or 1310nm | |
| Min. TX Output:- 20 dBm | |
| Max. TX Output: -14 dBm | |
| RX Sensitivity: -34 to -31 dBm | |
| Ethernet Transmission distance | Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm |
| Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm | |
| Power | |
| Input Voltage Range | +10 ~ +30VDC (Non-isolation) |
| Power consumption | 0.24A@24VDC, +/- 5% arrowed with 100M Full duplex |
| LED Indicator | Yes |
| Protection | Power reverse polarity protection |
| Frame Ground for EMS Protection | Yes |
| Connection | 5-Pin Removable Terminal Block |
| Mechanical | |
| Case | Plastic |
| Flammability | UL 94V-0 |
| Dimensions | 64mm x 110mm x 98mm (W x H x D) |
| Installation | DIN rail mount |
| Environmental | |
| Operating Temperature | 0 ~ +70°C |
| Storage Temperature | -20 ~ +85°C |
| Ambient Relative Humidity | 10% to 90% non-condensing |
1-888-492-6526
© 2010 Data Connect Enterprise
3405
Olandwood Court
Olney, Maryland 20832
