 |
|
|
1-888-492-6526
DATA CONNECT ANS209
9-Port Industrial Gigabit Fiber Switch
| ANS209-FT 8 10/100 +
100 Base-FX fiber-ST ANS209-MM 8 10/100 + 100 Base-FX fiber-Multimode SC ANS209-SM 8 10/100 + 100 Base-FX fiber-Single mode SC ANS209-FT-M 8 10/100 + 100 Base-FX fiber-ST+metal ANS209-MM-M 8 10/100 + 100 Base-FX fiber-Multimode SC+metal ANS209-SM-M 8 10/100 + 100 Base-FX fiber-Singlemode SC+metal |
The Data Connect ANS209FT (ST Connector; Multi-mode) is a Unmanaged 8-Port Industrial Ethernet(10/100Base-TX) to Fiber Optics(100Base-FX) converter that secures data transmission by using fiber optic transmission to provide immunity from EMI/RFI interference. It is used Ethernet for transmitting a signal up to 2 Km(6,600 ft), and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.
The Data Connect ANS209FT operates at either half or full duplex mode. In full duplex mode, range is 2km with 62.5/ 125μm fiber cables; in half duplex mode, range is 412m with 62.5/ 125μm fiber cables.
The Ethernet supports 10/ 100M auto-negotiation feature and auto MDI /MDIX function.
- Automatic MDI / MDI-X crossover for plug-and-play
- Each port supports both 10/100 Mbps speed auto negotiation
- Store-and-forward architecture
- Full duplex IEEE 802.3x and half duplex backpressure flow control
- 3.2 Gbps high performance memory bandwidth
- Integrated look-up engine with dedicated 1 K unicast MAC addresses.
- Supports +10~+30Vdc voltage
- Supports operating temperatures from -10 ~ +70°C
- DIN rail mount for industrial usage
| Technology | |
| Standards | IEEE802.3, 802.3u, 802.3x |
| Processing Type | Store & forward wire speed switching - no delays |
| MAC Addresses | 1024 |
| Memory Bandwidth | 3.2 Gbps |
| Flow Control | IEEE802.3x flow control, back pressure flow control |
| Interface | |
| RJ45 port |
10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDIX connection |
| Fiber Optic port | 100 Base-FX(Multi-mode; ST connector) |
| LED Indicators | 10/100M, Link/Act, Full duplex/Half duplex(Fiber Port) |
| Ethernet Isolation | 1500 Vrms 1 minute |
| Frame Ground for EMS Protection | Yes |
| Fiber Optic | Multi mode fiber cables:50/125, 62.5/125 or 100/140 μm |
| Distance :2 km, (62.5/125 μm recommended) for full duplex | |
| Wavelength : 1300 or 1310nm | |
| Min. TX Output:- 20 dBm | |
| Max. TX Output: -14 dBm | |
| RX Sensitivity: -34 to -31 dBm | |
| Ethernet Transmission distance | Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm |
| Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm | |
| Power | |
| Input Voltage Range | +10 ~ +30VDC (Non-isolation) |
| Power consumption | 0.17A@24VDC, +/- 5% arrowed with 100M Full duplex |
| LED Indicator | Yes |
| Protection | Power reverse polarity protection |
| Frame Ground for EMS Protection | Yes |
| Connection | 5-Pin Removable Terminal Block |
| Mechanical | |
| Case | Plastic |
| Flammability | UL 94V-0 |
| Dimensions | 64mm x 110mm x 98mm (W x H x D) |
| Installation | DIN rail mount |
| Environmental | |
| Operating Temperature | 0 ~ +70°C |
| Storage Temperature | -20 ~ +85°C |
| Ambient Relative Humidity | 10% to 90% non-condensing |
1-888-492-6526
© 2010 Data Connect Enterprise
3405
Olandwood Court
Olney, Maryland 20832
