 |
|
|
1-888-492-6526
DATA CONNECT MNS205-FT
5-PORT INDUSTRIAL 10/100 MANAGED FIBER SWITCH
PLASTIC OR METAL CASING
 MNS205-FT 3-100BTX, 2-100BFX-ST MNS205-MM 3-100BTX, 2-100BFX-Multimode SC MNS205-SM 3-100BTX, 2-100BFX-Singlemode SC |
 MNS205-FT-M 3-100BTX, 2-100BFX-ST +metal MNS205-MM-M 3-100BTX, 2-100BFX-Multimode +metal MNS205-SM-M 3-100BTX, 2-100BFX-Singlemode SC +metal |
The Data Connect MNS205-FT is a 5-Port Industrial Ethernet Real-Time Redundant Ring Switch with 2-Port Fiber (ST Connector; Multi-mode) that secures data transmission by using fiber optics transmission to provide immunity from EMI/RFI interference. It is used Ethernet for transmitting a signal up to 2 km(6,600 ft), and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.
Fiber port of Data Connect MNS205-FT operates at either half or full duplex mode. In full duplex mode, range is 2km with 62.5/ 125μm fiber cables; in half duplex mode, range is 412m with 62.5/ 125μm fiber cables. The Ethernet port of Data Connect MNS205-FT supports 10/ 100M auto-negotiation feature and auto MDI /MDIX function.
Built-in ICP DAS Cyber-Ring technique that enable multiple switches to be placed into a redundant ring. It detects and recovers from a fiber or copper link failure within approximately 50ms – for the majority of applications a seamless process. Modbus/TCP, Modbus/RTU and OPC supported, SCADA application can monitor status of Ethernet and fiber port with Modbus or OPC protocol.
Data Connect MNS205-FT provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the Data Connect MNS205-FT's power needs. And, the relay output facility can deliver warning signal while dual power or network link failure.
- Automatic MDI / MDI-X crossover for plug-and-play
- Each port supports both 10/100 Mbps speed auto negotiation
- Store-and-forward architecture
- Full duplex IEEE 802.3x and half duplex backpressure flow control
- 3.2Gbps high performance memory bandwidth
- Frame buffer memory : 512 Kbit
- Integrated look-up engine with dedicated 1 K unicast MAC addresses.
- Redundant Power Inputs +10 ~ +30V DC
Power failure alarm by relay output - Supports operating temperatures from 0 ~ +70°C
- DIN rail mount and Screw hole for wall mounting kit.
| Technology | |
| Standards | IEEE 802.3, IEEE 802.3u, IEEE802.3x |
| Processing Type | Store & forward wire speed switching - no delays |
| MAC addresses supported | 1024 |
| Memory Bandwidth | 3.2 Gbps |
| Flow Control | IEEE802.3x flow control, back pressure flow control |
| Redundant strategy | STP, Ring(ICP DAS) |
| Protocol | Modbus/RTU, Modbus/TCP, OPC, STP, Cyber Ring |
| Interface | |
| RJ45 port |
10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDIX connection |
| Fiber Optics Port | 100 Base-FX(Multi-mode; ST connector) |
| LED Indicators | 10/100M, Link/Act/Backup, Full duplex/Half duplex(Fiber Port) |
| Ethernet Isolation | 1500 Vrms 1 minute |
| Frame Ground for EMS Protection | Yes |
| Ethernet Transmission distance |
Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm |
| Fiber Optic Transmission distance |
Multi mode fiber cables:50/125, 62.5/125 or 100/140 μm |
| Distance :2 km, (62.5/125 μm recommended) for full duplex | |
| Wavelength : 1300 or 1310nm | |
| Min. TX Output: -20 dBm | |
| Max. TX Output: -14 dBm | |
| RX Sensitivity: -34 to -31 dBm | |
| Ethernet Cables | 10
Base-T (Cat.3, 4, 5 UTP cable; 100m Max.) 100 Base-TX (Cat.5 UTP cable; 100m Max.) |
| Management interface | Console, DIP/Rotary Switch |
| Alarm output | Relay |
| Power | |
| Input Voltage Range | +10 ~ +30VDC(Removable Terminal Block) |
| Power Input isolation | 1KV |
| Alarm Contact | One relay output with current carrying capacity of 2A @ 30 VDC |
| Power consumption | 0.3A@24Vdc (+/- 5%, arrowed) |
| Protection | Power reverse polarity protection |
| Frame Ground for EMS Protection | Yes |
| Connection | 7-Pin Removable Terminal Block |
| Mechanical | |
| Case | Plastic |
| Flammability | UL 94V-0 |
| Dimensions | 64mm x 110mm x 98mm (W x H x D) |
| Installation | DIN rail mount; Wall Mounting |
| Environmental | |
| Operating temperature | 0 °C~ +70°C |
| Storage Temperature | -20 ~ +85°C |
| Relative Humidity | 10% to 90% non-condensing |
| Include cable | |
| CA-090510 x 1 | |
1-888-492-6526
© 2010 Data Connect Enterprise
3405
Olandwood Court
Olney, Maryland 20832
