Data Connect will work with you to embed a Data Connect Pony Express modem module into your product. The modem can be installed in your existing rack chassis or will connect to your existing serial data interface. Because all of the Data Connect Pony Express modules are fully interchangeable, a single design will enable you to install any modem in your product. PE2.4 V.22bis, 2400 bps, Dial-up Modem Module PE9.6FP 9600 bps,Fast Poll Modem Module PE.9.6FPD  9600 bps Digital Fast Poll Modem Module PE14.4  V32bis, 14.4 Kbps Dial-up Modem Module PE14.4L  V32bis, 14.4 Kbps LL Modem Modle PE14.4EL  V.29, 9600 bps, or V.33, 14.4Kbps LL Modem  PE23 V23, 1200 bps, LL PE202T  Bell 202T, 1200 bps LL Modem Module PE-LDM  Limited Distance Modem Module PE-FO  Fiber Optic Line Driver Module PE485  RS232/RS485 Converter Module MM56  Embedded Modem Module V.92 with Separate Developer's Kit A Pony Express module is a part of every Data Connect® standalone and rack mount end user product — See MIU, MIU / PowerPort and Myriad™ products. These modules are also available to OEMs for integration into meters, controllers, RTUs, etc. The various models provide a choice of DC power supply voltage (regulated and unregulated) and data interface (RS232 or TTL), and are designed to operate over a wide range of temperatures (-40°C to 85°C). If the available power supply is limited (eg; a battery), the Pony Express module can be configured to fall into a “sleep” mode, or to completely power down, at times of inactivity. Dial modems include an auto-reset feature, whereby the modem configuration, if lost, can be restored by making an incoming call. Most dial modems also include an autodial feature, whereby the closure of, say, an alarm contact can initiate an outgoing call to a host computer or a pager. Data Connect will work with you to integrate a Pony Express modem module into your product. If necessary, we will design and manufacture a custom motherboard for the Pony Express module, such that a modem can be installed in your existing rack chassis or will connect to your existing serial data interface. A single design will enable you to install any modem in your product. CUSTOM MOTHERBOARDS Data Connect will work with you to integrate a Pony Express modem module into your product. If necessary, we will design and manufacture a custom motherboard for the Pony Express module, such that a modem can be installed in your existing rack chassis or will connect to your existing serial data interface. A single design will enable you to install any modem in your product. MYRIAD RACK MOUNT Modem Bank The Myriad Rack Mount Modem Bank is an industrial grade 19” 3U chassis with slots for 18 modem cards. METER MODEMS For automatic meter reading, Data Connect will integrate a modem into an electric, gas or water meter. Special features can be provided, such as off-hook detect and automatic call-in on power outage. TECHNICAL SPECIFICATIONS: Each Pony Express module is a fully functioning modem, complete with a 10-pin header for power and serial data, and an appropriate connector (eg; RJ11 or ST) for the analog or fiber optic data. Serial Data: RS232 or TTL Voltage: 5.5-9VDC unregulated or +5VDC±5% regulated Current: 50 to 150mA, depending on model Low Power Operating Modes: Dial modems can be configured to fall into a “sleep” mode, or to completely power down, at times of inactivity. In sleep mode, the inactive modem will draw less than 10mA and will instantly “wake up” on an incoming ring (RI) or transmit data (TxD) signal. In the power down mode, the current drain drops to 20µA and the modem will automatically turn on to full power within 400ms of receiving a DTR signal or an incoming call. Auto Reset Feature If a dial modem loses its configuration for any reason, the configuration is automatically restored by dialing the modem and allowing it to ring several times. Auto Dial Feature Most dial modems have the ability to automatically dial out to a stored phone number in the event of, say, an alarm condition.